|
1.INTRODUCTIONLinear spectroscopy in near-infrared (NIR) spectral range provides information on the molecular composition, structure, and conformation, affording tremendous potential for high-resolution, in-depth, label-free biological spectro-microscopy.1 In NIR spectroscopy, similar information to infrared spectroscopy is obtained by exciting the first overtone of infrared-active vibrational modes. The intensity and vibrational period of these harmonics depend on the quantity and types of the present molecules in the sample. Quantitative analysis is possible when the changes in the transmitted spectrum are proportional to the concentration of chemical components of the sample under scrutiny. Therefore, NIR spectroscopy has been a popular technique for identification, quantitative and qualitative analysis, and structure-correlation of molecular compositions. In particular, it is routinely used for the detection of the overtone and combination bands of the C-H, O-H, and N-H compositions.2 Additionally, as the electric filed in NIR spectral region supports a smaller diffraction limit than infrared, molecular information with higher spatial resolution can be obtained. Moreover, the lower cross-section of the overtone excitation allows for deeper penetration of the injected field to the sample, allowing for in-depth spectral imaging.3 Broadband measurements in this spectral region have been carried out mainly in the frequency domain.4 This approach suffers from two limitations: I) the detection of small absorption is limited to the intensity noise of the source, and II) the low detection dynamic range. To mitigate above-mentioned constraints, we introduce the concept of molecular fieldoscopy. In molecular fieldoscopy, an ultrashort, phase-coherent pulse is used for molecular excitation and afterwards the transmitted complex electric field that contains the molecular response is directly measured. Here, the electric field is detected in a background-free manner, eliminating the effect of the intensity noise of the source. Furthermore, measuring the complex electric field allows for extracting the full spectral phase information of the molecular response, adding a new dimension to the gained spectroscopic data. It is well known that the interaction of broadband ultrashort pulses with an ensemble of molecules at their resonance frequencies, results in a coherent scattering. The delayed response of the medium, known as free-induction decay (FID), can be explained by the Kramers-Kronig relation. During the interaction, photons at the resonance frequencies are slowed down compared to the other photons and appear at the trailing edge of the excitation pulse, due to the increase of the group refractive index of the medium at the vicinity of the resonance frequencies. The delayed response lasts for hundreds of picoseconds for molecules in the gas phase and down to several picoseconds in liquid phase. The FID carries information about the molecular composition and concentration. Therefore, by temporal detection of the coherent response, valuable spectroscopic information can be gained. Additionally, by using ultrashort pulses, the excitation pulse is confined to a time window of tens of femtosecond, which is significantly shorter than FID of the molecular sample under scrutiny. Here, the response emerging from the sample is separated temporally from the ultrashort excitation pulse, enabling for a background-free detection. As FID after the excitation pulse decreases exponentially, its earlier temporal detection results in a higher detection’s signal-to-noise ratio and therefore, sensitivity. Terahertz time-domain spectroscopy based on electro-optic sampling (EOS) has been a powerful method for the direct measurement of the electric field in mid-infrared and terahertz spectral region.5 However, its extension to NIR has been shown just recently, due to difficulties in the generation of short, phase-stable excitation pulses that are temporally synchronized with short sampling probe pulses.6 In what follows we report, to the best of our knowledge, the first measurement of the complex electric field of the water’s molecular response by using EOS in NIR spectral range. 2.EXPERIMENTAL SETUPWater plays a prominent role in biological interactions and life, with its first overtone of the symmetric stretch vibration appearing at 1450nm (6900cm–1) and a strong v2 + v3 combination band near 1930nm (5180cm–1). We aimed for the field detection of the water’s molecular response at its combination band for various molecular concentration. We chose acetic acid as the background solvent due to its sparse spectral response at this range. 2.1Near-infrared electro-optic samplingA home-built, diode-pumped Yb:YAG thin-disk regenerative amplifier operating at 5 kHz repetition rates was used as the frontend.7 1.8 mJ of the output energy of the laser was used to generate a carrier-to-envelope phase-stable, multi-octave, broadband spectrum spanning from 500 nm to 2500 nm.8 The broadband spectrum was divided into two portions: i) spectral region covering from 700 nm to 1400 nm, and ii) NIR region with spectral coverage from 1600 nm to 2500 nm. The two portions of the spectrum were amplified to the total energy of 25 μJ in two parallel single-stage optical parametric amplifiers. After amplification each channel was compressed to its Fourier transform limit, resulting in 5fs pulses centered at 1 μm and 18 fs pulses centered at 2 μm.9 The 18 fs, NIR pulses were used for excitation of combination bond of water molecules, while the 5 fs pulses at 1 μm were used as a probe in the EOS setup. The experimental setup of the EOS is depicted in Fig. 1. First, the NIR beam was focused by a 4 inch focal length off-axis parabolic mirror into the sample. Afterwards, the transmitted beam was collimated by another 4 inch focal length off-axis parabolic mirror. The sample was placed slightly after the focus to avoid filamentation of the NIR pulses. The beam size on the sample was 200 μm, full width at half maximum (FWHM). The probe pulses were collinearly combined with the transmitted light from the sample by using an ultra-broadband wire grid polarizer (Thorlabs, WP25L-UB). Subsequently, both beams were focused by a 2 inch focal length off-axis parabolic mirror into a 50 μm-thick BBO (Type II) crystal (CASTECH) at the phase matching angle of θ = 25°. The probe and NIR beams were orthogonally polarized along the ordinary (o) and extraordinary (e) axes of the nonlinear crystal, respectively. By temporal and spatial overlap of the two pulses in the crystal, sum-frequency signal centered at 670 nm was generated. The sum-frequency signal was polarized along the extraordinary (e) axis of the nonlinear crystal and spectrally overlaps with the high-frequency components of the ordinarily polarized probe pulses. In order to enhance the EOS signal at the detectors, spectral region between 650 nm and 750 nm was filtered out by using a 650 nm long-pass (Thorlabs, FEL0650) and a 750 nm short-pass (Edmund Optics, 64-324) filters.10 The generated nonlinear signal induces polarization rotation in the probe pulses as a function of the relative timing of the probe and NIR pulses. The induced electro-optic signal was detected with an ellipsometer consisting of a quarter-wave plate (Thorlabs, AQWP05M-600), Wollaston prism (Thorlabs, WP10), and a home-built balanced detector. In the absence of the NIR beam, the ellipsometer is aligned to equally split and balance the power of the probe pulses at the pair of photodiodes. Therefore, the difference between the photocurrents of the two detectors is equal to zero. In the presence of the NIR pulses, the difference is imbalanced and varies relative to the temporal delay of the probe pulses. The electronic data from the balanced detector is recorded by using a lock-in amplifier (Stanford Research Systems, SR830-DSP) while the NIR pulses were modulated at 2.5 kHz (half of the laser’s repetition rate) with a mechanical chopper (Thorlabs, MC2000B-EC). In parallel for a precise temporal delay scan, the mechanical delay stage (Physik Instrumente, V-528.1AA) was tracked with a Mach-Zehnder-type interferometric delay tracking setup (SmarAct GmbH, PicoScale). The setup employs the beam of a 1.55 μm continuous-wave distributed-feedback laser diode, propagating along the NIR and probe beam-paths.11 A series of measurements were performed to estimate the detection dynamic range of the EOS setup in the absence of the liquid sample. First, the energy of the NIR pulses was attenuated by using a series of neutral density filters with different optical densities (ODs) and afterwards their electric field were measured by EOS. Figure 2 a) illustrates the sampled waveforms for different attenuations. The black curve shows the electric field of the unatenuated NIR pulses. The red curve shows the detectable NIR pulses by EOS with the average power of 650nanowatts (power attenuation by filters at the OD of 3.1). The corresponding spectra of EOS traces for five different attenuations (OD of 0, 0.8, 1.5, 2.2, and 3.1) are shown in Fig. 2 b). The spectra were obtained by Fourier transformation of the measured electric filed. As can be seen, at the highest attenuation the bandwidth of the retrieved spectrum is limited to spectral components with the highest spectral intensity. 2.2Sample preparationAcetic acid (Sigma-Aldrich, ReagentPlus, 99%, A6283) and deionized water were used to create solution samples at six different concentrations between 0 Molar to 55.6 Molar (0% - 100%). Afterwards, different mixtures were injected to a sample holder (Harrick Scientific, DLC-M25) consisting of two sapphire windows with a thickness of 2.3 mm. The sample’s thickness for all the measurements was 500 μm. 3.RESULTS AND DISCUSSIONTo detect the FID of water molecules, the mixture of acetic acid and water with different concentrations was placed in the sample holder and the transmitted electric field was measured by EOS. The delay stage was scanned over 450 μm with the speed of 1.7 μm/s, corresponding to a single shot detection at each delay position. Background measurements were taken with an empty sample holder and pure acetic acid serving as blank (see Fig. 3 a)). As can be seen in the inset, the amplitude of the excitation pulses goes to zero at temporal delays above 200 fs. By adding the sample, the molecular FID is formed and can be detected free of background at temporal delays beyond 200 fs. Figure 3 b) shows the measured transmitted electric field for the mixture of water and acetic acid at two high concentrations. At high water concentrations the transmitted main pulse is chirped. The NIR response of water molecules is clearly distinguished from acetic acid at 50%, and 100%,. To evaluate the sensitivity of the system, measurements of lower water’s concentrations (10%, 5%, and 3%) were carried out. As is shown in Fig. 3 c), the molecular response is detectable by naked eye for water concentration as low as 3%. A similar study12 was reported in the frequency domain on water molecules in methanol solvent by using a Guided Wave NIR-O Process, fiber-coupled, NIR Spectrometry with the core diameter of 500 μm. In this experiment, the water molecules in methanol solvent were placed in a 10 mm-thick sample holder. The combination bond of water molecules could be detected down to 0.1% water concentration. Calibrating our measurements with a 500μm sample thickness and a 200μm laser beam size (shown in Fig. 3c)), to 10 mm of sample thickness and 500μm of beam diameter, results in 0.075% equivalent detectable water concentration by EOS. 4.CONCLUSION AND OUTLOOKWe presented a novel approach, which we dubbed molecular fieldoscopy, for detection of the complex electric field of molecular response in NIR spectral range. Here, exciting molecules with ultrashort pulses allows for background-free detection of the molecular response. By employing broadband excitation pulses in combination with EOS, the entire molecular vibrations in the fingerprint region can be simultaneously excited and detected. In this regards, we showed the potential of Yb:YAG thin-disk lasers for generating the required multi-octave spectrum and demonstrated the first proof of principle field-detection of water molecule’s vibration at 1.9 μm at different molecular concentrations. Our current detection sensitivity is comparable to the conventional spec-troscopy techniques and limited to the stability of the interferometer and the repetition rate of the laser. However, employing a frontend at megahertz repetition rates13 holds promise for enhancing the detection sensitivity to unparalleled values. Moreover, combining the concept of molecular fieldoscopy with exciting nonlinear techniques such as two-dimensional spectroscopy, holds promise to increase our understanding of molecular dynamics, for example in water. Water in liquid phase, consists of a molecular network with molecular dynamics at various time scales, from several picoseconds to tens of femtoseconds. The intermolecular OH-bond stretching and bending has the shortest vibrational period at 10 fs and 20 fs, respectively. On a time scale of several hundreds of femtoseconds, liberational motions, and the H-bonds stretching and bending occur. Last but not least the exchange of hydrogen-bond partners via breaking and reforming of stable H-bonds occurs in a time range between 1-5 ps.14 Femtosecond molecular fieldoscopy is capable of detecting the complex electric field of the water response at all above-mentioned time scales with high sensitivity, and may allow for resolving many unknown aspects of water’s molecular dynamic. REFERENCESJöbsis, F.F.,
“Noninvasive, infrared monitoring of cerebral and myocardial oxygen sufficiency and circulatory parameters.,”
Science (New York, N.Y.), 198 1264
–1267
(1977). https://doi.org/10.1126/science.929199 Google Scholar
Andrews, N. L. P., MacLean, A. G., Saunders, J. E., Barnes, J. A., Loock, H.-P., Saad, M., Jia, C., Ramaswamy, K., and Chen, L. R.,
“Quantification of different water species in acetone using a NIR-triple-wavelength fiber laser,”
Optics Express, 22
(16), 19337
(2014). https://doi.org/10.1364/OE.22.019337 Google Scholar
Wang, H.-W., Chai, N., Wang, P., Hu, S., Dou, W., Umulis, D., Wang, L. V., Sturek, M., Lucht, R., and Cheng, J.-X.,
“Label-Free Bond-Selective Imaging by Listening to Vibrationally Excited Molecules,”
Physical Review Letters, 106 238106
(2011). https://doi.org/10.1103/PhysRevLett.106.238106 Google Scholar
Pasquini, C.,
“Near Infrared Spectroscopy: fundamentals, practical aspects and analytical applications,”
Journal of the Brazilian Chemical Society, 14 198
–219
(2003). https://doi.org/10.1590/S0103-50532003000200006 Google Scholar
Dhillon, S. S., Vitiello, M. S., Linfield, E. H., Davies, A. G., Hoffmann, M. C., Booske, J., Paoloni, C., Gensch, M., Weightman, P., Williams, G. P., Castro-Camus, E., Cumming, D. R. S., Simoens, F., Escorcia-Carranza, I., Grant, J., Lucyszyn, S., Kuwata-Gonokami, M., Konishi, K., Koch, M., Schmuttenmaer, C. A., Cocker, T. L., Huber, R., Markelz, A. G., Taylor, Z. D., Wallace, V. P., Axel Zeitler, J., Sibik, J., Korter, T. M., Ellison, B., Rea, S., Goldsmith, P., Cooper, K. B., Appleby, R., Pardo, D., Huggard, P. G., Krozer, V., Shams, H., Fice, M., Renaud, C., Seeds, A., Stöhr, A., Naftaly, M., Ridler, N., Clarke, R., Cunningham, J. E., and Johnston, M. B.,
“The 2017 terahertz science and technology roadmap,”
Journal of Physics D: Applied Physics, 50 043001
(2017). https://doi.org/10.1088/1361-6463/50/4/043001 Google Scholar
Keiber, S., Sederberg, S., Schwarz, A., Trubetskov, M., Pervak, V., Krausz, F., and Karpowicz, N.,
“Electro-optic sampling of near-infrared waveforms,”
Nature Photonics, 10 159
–162
(2016). https://doi.org/10.1038/nphoton.2015.269 Google Scholar
Fattahi, H., Alismail, A., Wang, H., Brons, J., Pronin, O., Buberl, T., Vámos, L., Arisholm, G., Azzeer, A. M., and Krausz, F.,
“High-power, 1-ps, all-Yb:YAG thin-disk regenerative amplifier,”
Optics Letters, 41 1126
–1129
(2016). https://doi.org/10.1364/OL.41.001126 Google Scholar
Fattahi, H., Wang, H., Alismail, A., Arisholm, G., Pervak, V., Azzeer, A. M., and Krausz, F.,
“Near-PHz-bandwidth, phase-stable continua generated from a Yb:YAG thin-disk amplifier,”
Optics Express, 24 24337
–24346
(2016). https://doi.org/10.1364/OE.24.024337 Google Scholar
Fattahi, H., Wang, H., Alismail, A., and Krausz, F.,
“Towards high-power, multi-TW light transients,”
in [Conference on Lasers and Electro-Optics], SM1M.6,
(2016). https://doi.org/10.1364/CLEO_SI.2016.SM1M.6 Google Scholar
Porer, M., Ménard, J.-M., and Huber, R.,
“Shot noise reduced terahertz detection via spectrally postfiltered electro-optic sampling.,”
Optics letters, 39
(8), 2435
–2438
(2014). https://doi.org/10.1364/OL.39.002435 Google Scholar
Schweinberger, W., Vamos, L., Xu, J., Hussain, S. A., Baune, C., Rode, S., and Pupeza, I.,
“Interferometric delay tracking for low-noise Mach-Zehnder-type scanning measurements,”
Accepted in Optics Express, Google Scholar
Wave, G.,
“Measuring Water Concentration in Solvents with NIR Spectroscopy.,”
Google Scholar
Fattahi, H., Barros, H. G., Gorjan, M., Nubbemeyer, T., Alsaif, B., Teisset, C. Y., Schultze, M., Prinz, S., Haefner, M., Ueffing, M., Alismail, A., Vámos, L., Schwarz, A., Pronin, O., Brons, J., Geng, X. T., Arisholm, G., Ciappina, M., Yakovlev, V. S., Kim, D.-E., Azzeer, A. M., Karpowicz, N., Sutter, D., Major, Z., Metzger, T., and Krausz, F.,
“Third-generation femtosecond technology,”
Optica, 1 45
–63
(2014). https://doi.org/10.1364/OPTICA.1.000045 Google Scholar
Laage, D., Elsaesser, T., and Hynes, J. T.,
“Water Dynamics in the Hydration Shells of Biomolecules,”
Chemical Reviews, 117 10694
–10725
(2017). https://doi.org/10.1021/acs.chemrev.6b00765 Google Scholar
|