|
1.INTRODUCTIONEUCLID mission1 has been selected by ESA in 2012 in the context of the Cosmic Vision program to study the nature of dark energy and dark matter. The launch of the mission is foreseen in 2021. The mission is designed to map the geometry of the dark Universe by investigating the distance-redshift relationship and the evolution of cosmic structures thanks to two scientific instruments: the Near Infrared Spectroscopic Photometer (NISP)2 and the Visible instrument (VIS)3. The NISP channel of Euclid is dedicated to measure the redshift of millions of galaxies and to analyze their spatial distribution in the Universe. NISP works with both photometric and spectroscopic modes by switching between broadband filters and grisms, mounted on two rotating wheels, to acquire data of the same field. NISP instrument is made by an European consortium led by Centre National des Etudes Spatiales (CNES) that includes laboratory and industries mainly from France, Germany, Italy and Spain. The Laboratoire d’Astrophysique de Marseille (LAM) is deeply involved in the development and the test of the NISP as LAM is responsible for the integration, alignment and test of the instrument. The integration of the Flight Model (FM) is already started and will be finished by end of 2018. The NISP FM will be tested and validated under vacuum and thermal conditions at LAM in ERIOS chamber4, a 90m3 chamber developed by LAM to test optical instruments at cryogenics temperature and high vacuum. The goal of this TB/TV test is to qualify the instrument in its operating environment, to measure the optical performance of the instrument, and validate its functionality before its delivery to the payload module. To realize properly the test in ERIOS, a global Ground Support Equipment (GSE) called the Verification Ground System (VGS) is developed by LAM and its Danish partners. The VGS is a complex set of GSE made of i) a telescope simulator to simulate the EUCLID telescope for NISP optical performance tests, ii) a thermal environment to simulate the Euclid PayLoad Module (PLM) thermal interfaces, iii) a set of mechanical interfaces to align and install all the parts into ERIOS, iv) the NISP Electrical GSE (EGSE) to control the instrument during the test and v) a Metrology Verification System (MVS) to measure the positions of NISP and the telescope simulator during the test. We present in this article first the test objectives and configuration of the NISP campaign. Then we describe the different parts of the VGS and their performance. 2.NISP TEST CAMPAIGN DESCRIPTION2.1NISP test campaign goalAfter the integration and alignment of NISP instrument2, it is required to validate the optical performance of the full-assembled instrument and its main functionality. It is then foreseen to do two complete thermal performance tests of NISP FM to validate the instrument before and after the acceptance vibration test of the instrument. The test, realized in thermal-vacuum environment, shall:
The NISP test campaign will take place at LAM in ERIOS chamber4 and will be done thank to the Verification Ground System (VGS), a set of Ground Support Equipment (GSE) specially developed for NISP. The VGS is installed in ERIOS and simulates the EUCLID telescope and the thermal interfaces of the payload to ensure that the NISP test will be done in the needed conditions. The VGS is a set of GSE that allows testing NISP FM before the launch. NISP test campaign and the development of the VGS represent a great challenge due to the complexity of the installation and components to provide. Figure 1 presents the CAD view of the NISP test configuration inside ERIOS. We show in this figure the telescope simulator, part of the VGS, the thermal and mechanical interfaces for the test, and the metrology system and of course NISP instrument. In addition, NISP is surrounded by a thermal enclosure, not shown here, to ensure the good thermal environment during the test. 2.2VGS technical specificationsThe VGS has to answer to technical specifications provided by NISP Assembly Integration Verification (AIV) team. The main specifications are:
3.VERIFICATION GROUND SYSTEM DESCRIPTIONThe VGS, described in the following sections, answers to these specifications to provide the good GSE for NISP test campaign purpose. It is made of an optical GSE, thermal GSE, mechanical GSE and a metrology mean. 3.1The Optical Ground Support Equipment (OGSE): the telescope simulatorThe concept of the OGSE developed for NISP is to simulate the F/20 EUCLID telescope beam thanks to an elliptical mirror positioned on stages that allow the telescope to move in five degrees of freedom to illuminate the entire NISP FoV wherever it is needed. The OGSE is made of two main parts: the NISP Telescope Simulator (NI-TS) itself that mimics EUCLID telescope, and a Focal Plane Unit (FPU) that is used to simulate the EUCLID object plane i.e where the focal plane will be in absence of NISP optics. The two parts are shown respectively in Figure 2 and Figure 3. The FPU is only used to validate the NI-TS functionality at cold during the acceptance of the VGS and will be not used during the test with NISP. The main goal of the NI-TS is to provide a stable focal distance to NISP to allow the measurement of the position of NISP object plane. To achieve this goal, the NI-TS is designed with a stable thermal interface done by the thermal flexures between the telescope itself and the motor assembly. This is one of the main challenges for the NI-TS design as the different parts of the NI-TS operate at different temperature and in a warmer environment than NISP. The NI-TS itself is made of two units: the Active Telescope Support unit (ATS) that moves the second unit, the Telescope Simulator (TS), around to illuminate the full NISP FoV. The ATS is an assembly of 5 motors providing 5 degrees of freedom. It is made of 3 linear and 2 rotational high precision stages with remote controlled motor and absolute encoder to provide position of the unit. These stages are vacuum compatible and with a large moving range to commit with NISP need and in particular, to allow a scanning of the focus to find NISP best focus. The ATS is directly in interface with ERIOS bench thanks to 3 shims under the last translation stage baseplate. The TS is an off-axis elliptical mirror assembled to a baseplate thanks to optical contact done by Winlight Optics5. On the same baseplate, a pinhole is set at the entrance focus to provide an interface for the source. It is a single surface optical design, which provides an unobstructed system. The design of the TS is to provide a first focal point at 500mm while the distance from the mirror vertex to the second focal point is 3000mm. The whole TS assembly is made of Silica to ensure a good stability of the focal distance of the telescope and will operate at 165K to limit impact of the temperature on the stability of the focal distance (the CTE of the silica being null at this temperature). The telescope is illuminated through a 2μm diameter pinhole placed in the primary focus and should provide uniform illumination of the 160mm diameter aperture. The focus of the telescope should be known with a precision better than 20μm at operational temperature meaning that the distance from the pinhole to the mirror should be stable within 0.5μm. An accurate measurement of the focal distance is done at ambient temperature thanks to a Coordinate Measurement Machine (CMM) with high precision and then at cold temperature thanks to the Metrology Verification System (MVS), described in subsection 3.3. The WFE is lower than 30nm rms over the 160mm diameter aperture to ensure a good image quality on NISP during the performance test. In order to minimize stray light during NISP test, the telescope is surrounded by a baffle made of several vanes. More details on the NI-TS design and on the FPU design can be found in [4]. At the entrance of the TS, a cold fiber is connected to the illumination system used for the NI-TS. It is made of a monochromator that feds from a continuum laser source. The output from the monochromator is delivered to a cryogenic fiber through a pair of vacuum windows in interface with ERIOS chamber. A cooled Neutral Density (ND) filter suppresses the thermal background. The flux can be adjusted in large steps via ND filters mounted in a filter wheel also serving as order-sorter for the grating based monochromator, The flux can be fine-tuned using a variable rotating ND filter. A spectral lamp and an etalon are available for wavelength calibration and can be selected using linear motions. The source module, installed outside ERIOS chamber, is shown in Figure 3. The NI-TS is provided with a Telescope Control Computer (TCC) to control the motors position, the light illumination and intensity and to read data from the FPU and the thermal control of the NI-TS. 3.2Thermal and mechanical ground support equipmentThe Thermal and Mechanical Ground Support Equipment also called TMVS provide thermal and mechanical interfaces for NISP. It simulates the PLM thermal environment. The radiative thermal environment consists of ERIOS liquid nitrogen shrouds that are cooled down at 90K. The TMVS has also to provide conductive interfaces for NIOMADA, Warm Electronic and for the intermediate harness of the NISP detector system. A complete description of the TMVS is provided in [4]. For the optical performance test case, the temperature of the detector is set at 90K with a stability of 20mK/h while the rest of the instrument is maintained at 130K. Intermediate liquid nitrogen loops are designed to fill auxiliary tanks under NISP, near the detector system and near the configuration to ensure the best regulation of the thermal interfaces. We have an autonomy of 30 hours between two filling and we manage the cooling down phase in order to keep detectors warmer than the rest of the instrument during the cool down. Figure 4 shows the different elements of the TMVS during the blank test done in December 2017. We show in this picture the mechanical interfaces of NISP that is used to cool down the NISP feet and the auxiliary tanks. The whole system has been installed in ERIOS chamber to perform an acceptance test of the thermal interfaces and to demonstrate that the thermal performance needed for NISP TB/TV can be reached. The test done in December 2017 was successful, as it has validated:
In addition, we have characterized the thermal conductance of the detectors and its electronics cold straps and measure the cold fiber interface temperature used by the telescope simulator to avoid introducing thermal background with the source. We have also installed during the test an engineering model of one NISP detector near the pupil of the instrument to estimate the thermal background of the chamber during NISP test. Even if the measurement is coarse, it has shown a measured dark current around 52 ADU/f that is fully compatible with the needs for NISP test. Finally, this test has also allowed measuring a set of reflectors at cold and has validated a new step for the metrology described in the following section. 3.3Metrology equipmentThe VGS included also a Metrology Verification system (MVS) to provide at operational temperature the measurement of reflectors installed on the NI-TS and on NISP. The metrology system is specially developed for NISP purpose and it is made of:
The metrology configuration is shown in Figure 6. The metrology has been developed in parallel of the other parts of the VGS. In particular, it has been required to demonstrate the performance that can be reached by the laser tracker in this configuration that was not usual. A dedicated test campaign has been done in September 2017 to validate the measurement of the laser tracker through a curved window and at vacuum. All details of this study can be found in [5]. We have demonstrated with this test that the measurement of the laser tracker for NISP purpose will have an error better than 100μm at vacuum and cold temperature. 3.4Control / Command configurationThe whole VGS will be in interface with NISP and its Electrical GSE (EGSE) for NISP FM TB/TV test. A full description of the EGSE is provided in [7] and [8]. We only present in this article the architecture provided for the test that will allow having a simple interface between all the VGS parts and NISP. The NISP EGSE is made of the NI-WE SCOE, the NISP Central Checkout System (NI-CCS), the EGSE harnesses between the computers and the hardware and the NISP Instrument WorkStation (NI-IWS). All these parts are on an internal network that should be compatible with the PLM network and the NISP performance test. The EGSE is developed for the test of NISP instrument on ground and its goal is to control NISP instrument during the test phase. It will launch the scripts for the test, acquire the data from the detectors and provide all the telemetry from the instrument. For the NISP performance test, it is needed to add an interface between NISP instrument and the NI-TS to control the light sources and the motor of the telescope during the acquisition sequence planned for NISP test. This link is done by the EGSE though the EDEN protocol. In addition, a Database Builder (DB) will recover all information from ERIOS, the VGS and NISP EGSE. It will build the high-level database permitting to associate the complete set-up configuration for the instrument and the GSEs to each instrument exposure. It will be a memory of the tests performed at LAM with the VGS. Finally, an analysis computer will be linked to the whole architecture to allow analysis in real time or from remote of the data. 4.CONCLUSIONWe have presented in this article a complete description of the VGS, a ground support equipment developed at LAM to test NISP instrument at vacuum and cold. The VGS will be used during the performance test campaign of NISP to validate the main functionality of the instrument and its main performance in photometric and spectroscopic modes. The VGS is made of an optical part, which simulates the EUCLID telescope, a set of thermal and mechanical parts to ensure the thermal stability of NISP during the test, a control / command system to control the instrument together with its GSE during the test and a metrology system. The VGS is currently fully delivered at LAM and final validations have been started for the telescope simulator. We have already shown the good performance reached by the metrology and the TMVS. A blank test of the complete VGS is scheduled for October 2018 to demonstrate the performance and quality of the optical GSE. The VGS will be delivered to NISP project in November 2018, just before the start of the NISP test campaign, scheduled in January 2019. The development of the VGS represents a great challenge as many functionalities are required and many institutes are involved. REFERENCESG. Racca; R. Laureijs; L. Stagnaro; J.-C. Salvignol,
“The Euclid mission design,”
in Proc. SPIE 9904, Space Telescopes and Instrumentation 2016: Optical, Infrared, and Millimeter Wave,
99040
–23
(2016). Google Scholar
T. Maciaszek,
“Euclid near infrared spectrophotometer instrument concept and first test results at the end of phase C,”
in Proc. SPIE 9904, Space Telescopes and Instrumentation 2016: Optical, Infrared, and Millimeter Wave,
99040
–18
(2016). Google Scholar
M. Cropper; S. Pottinger; S. Niemi; J. Denniston,
“VIS: the visible imager for Euclid,”
in Proc. SPIE 9904, Space Telescopes and Instrumentation 2016: Optical, Infrared, and Millimeter Wave,
99040
–16
(2016). Google Scholar
A. Costille; M. Carle; C. Fabron; E. Prieto; F. Beaumont,
“How to test NISP instrument for EUCLID mission in laboratory,”
in Proc. SPIE 9912, Space Telescopes and Instrumentation 2016: Optical, Infrared, and Millimeter Wave,
9904
–95
(2016). Google Scholar
WINLIGHT Optics, http://www.winlight-system.com/ Google Scholar
A. Costille; F. Beaumont; E. Prieto; M. Carle,
“3D metrology with a laser tracker inside a vacuum chamber for NISP test campaign,”
in Proc. SPIE 10706, Advances in Optical and Mechanical Technologies for Telescopes and Instrumentation III 2018,
107061P
(2018). Google Scholar
E. Franceschi,
“EGSE customization for the Euclid NISP Instrument AIV/AIT activities,”
in Proc. SPIE 9904, Space Telescopes and Instrumentation 2016: Optical, Infrared, and Millimeter Wave,
9904
–97
(2016). Google Scholar
M. Trifoglio,
“Instrument Workstation for the EGSE of the Near Infrared Spectro-Photometer instrument (NISP) of the EUCLID mission,”
in Proc. SPIE 9904, Space Telescopes and Instrumentation 2016: Optical, Infrared, and Millimeter Wave,
9904
–231
(2016). Google Scholar
|