We recently developed a holmium-doped triple-clad fiber (Ho-3CF) for laser emission beyond 2.1 μm. In a clad-pumped fiber laser oscillator emitting at 2.12 μm, we obtained an optical efficiency of 73% with respect to the absorbed pump power at 1.94 μm, and a maximum signal power of 62 W. We present here the comparison between the laser measurements and a numerical simulation, together with the measurements of the required physical parameters (crosssections, attenuations…). The alumino-silicate core composition of our initial Ho-3CF samples required the introduction of a pedestal to preserve the single spatial-mode guiding. We also present our preliminary results on a new aluminophospho-silicate core composition, in order to suppress the initial pedestal and simplify the fabrication process. Both samples were also analyzed in core-pumped laser configuration.
We present here the development of ultra-low NA large mode area neodymium doped alumino-phospho-silica fibers with different clad-to-core ratios for high power laser emission around 910nm. This ratio is determinant in the competition between the 3-level transition at 910nm and 4-level transition of neodymium at 1060nm. The study shows that the 30/130µm (core/cladding) fiber was the most efficient, with a record output power of 83W at 910nm, yielding a 47% slope efficiency and a good beam quality (M²~1.5). Parasitic power at 1060nm was kept lower than 1W and no sign of roll-off was observed at maximum pump power.
We present in this work, the development of a nanosecond pulsed Master-Oscillator Power-Amplifier (MOPA) laser system near 905 nm based on the 3-level transition of Neodymium using a novel low NA polarization-maintaining Nd-doped silica fiber with a 30µm core and 130µm cladding. The MOPA delivered up to 24 W of average power (0.6 mJ energy per pulse) with good beam quality (M²~1.4). Cascaded LBO and BBO crystals are used respectively for second-harmonic generation and fourth-harmonic generation, giving respectively average output powers of 4.9W at 452nm (conversion efficiency of 20%) and 550mW at 226nm (conversion efficiency of 10%).
We present the fabrication by Surface Plasma Chemical Vapor Deposition (SPCVD) and All Solution Doping (ASD) of step-index Nd-doped fibers with a 30/125μm (core/cladding diameters) geometry and a low numerical aperture (NA) near 0.05. A phospho-alumino-silicate (SiO2-Al2O3-P2O5-Nd2O3) core composition was used to reduce the formation of Nd3+ ions clusters while keeping a low refractive index through the peculiar AlPO4 chemical complex. Operated in CW laser regime, a 0.053 NA fiber generated up to 17W of output power at 921nm, limited by the available pump power at 808nm (51W), yielding a 37% power conversion efficiency. The profile of the output beam for a bend diameter of ~12cm is gaussian and nearly diffraction limited (M2 ~1.1). This is in good agreement with the large discrepancy, in terms of calculated bending losses, between the fundamental LP01 and the higher order modes.
Erbium-ytterbium co-doped phospho-silicate double-clad fibers are used in many applications were powerful 1.5 μm sources are needed, such as telecommunication systems, LIDAR, medical lasers and much more. These fibers are typically pumped with diodes emitting at 915, 940 or 976nm to excite Ytterbium ions, which in turn transfer their energy to erbium ions through a phonon-assisted mechanism, thus leading to 1.5 μm emission. This energy transfer requires a large phosphorous content in the core of the fiber and therefore these fibers exhibit typically high numerical apertures. Properly optimized, the ytterbium to erbium ratio will minimize parasitic emission at 1 μm which provokes system failures through non-controlled spurious laser effects. We have recently observed, on such optimized fibers exhibiting 12 μm core diameter and 0.20 numerical aperture, that long term operation in CW mode in both amplifier and laser configuration, leads to a slow and irreversible decrease of the output power. This phenomenon starts at moderate signal power of just 7W and increases rapidly with the output power. This phenomenon is also observed in polarization maintaining version of the very same fibers. We have studied this phenomenon which resembles the well-known photodarkening effect in Ytterbium doped fibers. Our experiments show that all the commercially available fibers tested exhibit the same behavior. We will present a tentative explanation of the phenomenon and some solutions we implemented to drastically stabilize the output powers up to 20W enabling the use of such fibers in many industrials applications.
Large-Mode-Area (LMA) fibers are key elements in modern high power fiber lasers operating at 1 μm. LMA fibers are highly ytterbium-doped and require a fine control of the core refractive index (RI) close to the silica level. These low RI have been achieved with multi-component materials elaborated using a full-vapor phase Surface Plasma Chemical Vapor Deposition (SPCVD) process, enabling the fabrication of large core diameter preforms (up to 4 millimeters). Following the technology demonstration, presented in Photonics West 2017, with results on 10/130 (core-to-clad diameters (in μm) ratio) fibers, this paper aims to present updated results obtained for double-clad 11/130, 20/130 and 20/400 LMA fibers, with numerical apertures at, respectively, 0.08 and 0.065. The study is based on aluminosilicate core material co-doped either with fluorine or phosphorus to achieve optimal radial RI tailoring. The fiber produced exhibit low background losses (<20dB/km at 1100nm) and high power conversion efficiencies, up to 74% for output powers of 100W limited by our test setup. The Gaussian beam quality has been evaluated using the M2 measurement. Photodarkening behavior will be discussed for both fluorine and phosphorus-doped aluminosilicate materials and particularly the use of cerium as co-dopant. The SPCVD technology can indeed be used for the production of Yb-doped LMA fibers. Current development is now focused on other rare-earth doped fibers.
One key parameter in the race toward ever-higher power fiber lasers remains the rare earth doped optical core quality. Modern Large Mode Area (LMA) fibers require a fine radial control of the core refractive index (RI) close to the silica level. These low RI are achieved with multi-component materials that cannot be readily obtained using conventional solution doping based Modified Chemical Vapor Deposition (MCVD) technology. This paper presents a study of such optical material obtained through a full-vapor phase Surface Plasma Chemical Vapor Deposition (SPCVD). The SPCVD process generates straight glassy films on the inner surface of a thermally regulated synthetic silica tube under vacuum. The first part of the presented results points out the feasibility of ytterbium-doped aluminosilicate fibers by this process. In the second part we describe the challenge controlling the refractive index throughout the core diameter when using volatile fluorine to create efficient LMA fiber profiles. It has been demonstrated that it is possible to counter-act the loss of fluorine at the center of the core by adjusting the core composition locally. Our materials yielded, when used in optical fibers with numerical apertures ranging from 0.07 to 0.09, power conversion efficiency up to 76% and low background losses below 20 dB/km at 1100nm. Photodarkening has been measured to be similar to equivalent MCVD based fibers. The use of cerium as a co-dopant allowed for a complete mitigation of this laser lifetime detrimental effect. The SPCVD process enables high capacity preforms and is particularly versatile when it comes to radial tailoring of both rare earth doping level and RI. Large core diameter preforms - up to 4mm - were successfully produced.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.