|
I.INTRODUCTIONThese last years, the space industry has shown an increasing interest for photonics, as an enabling technology to address new satellite architectures and sub-system applications. The most attractive perspectives consist in taking benefit from the ground optical communication technology, as it offers a wide range of possibilities, which are of strong interest for both civilian and defense applications. In spite of past researches, this technology is still not yet ready for space, a major lock being the availability of the so-called EDFA ”Erbium-Doped Fiber Amplifier”, which is strongly degraded by the harsh radiative space environment. It was clearly identified that the radiation-affected component of the EDFA is the Erbium-Doped Fiber (EDF)itself[1]. Indeed, up to now, EDFs fabricated by state of art technology do not fulfill the requirements because the radiations produce a dramatic increase of the fiber background losses. These losses lead to huge gain reduction at the end-of-life of the EDF. II.STATE OF THE ARTThe degradation of the EDFs, called ”Radio-Induced-Absorption” (RIA), is not due to the insertion of the Erbium ion itself in the host matrix, but to the addition of a significant amount of Aluminum as co-doping atom in classical fabrication processes. Unfortunately, whereas Aluminum facilitates the inclusion of the Erbium ions in the glass and reduces quenching effects, it also induces structural defects in the host matrix, resulting in strong RIA levels after irradiation[2], [3]. At this time, three main approaches have been explored to reduce the amplifier gain and optical power degradation originating from the RIA. The first one consists in fabricating shorter amplifiers [4]. Indeed, because the overall radiation induced losses grow as an exponential function of the amplifier fiber length, the first already visited way to reduce EDFA degradation has consisted in increasing Erbium concentration by means of conventional doping techniques, leading to huge concentrations of both Aluminum and Erbium. However, this approach is limited by the increase of Aluminum-induced RIA and / or by the quenching effect, which both impact optical gain and output power. Another possibility consists in fiber hydrogenation, which is known to reduce the amount of traps in silica fibers. This way is very efficient regarding the achievable reduction of the RIA[5]. Unfortunately, it is very well known that the hydrogen reaction with the silica defects leads to the formation of hydroxyl group (OH)and sometimes hydrides (SiH). The OH overtones and combinational vibration in silica glass introduce the peak absorption in IR region. So, its impact to the background losses depends on the wavelength and it is therefore difficult to predict the resulting attenuation spectrum; typically, 1 ppm of formed OH induces 40 dB/km of losses at 1385 nm and 1 dB/km at 940 nm[6], [7]. The resulting attenuation at both pump and signal wavelengths will obviously impact the maximum achievable gain or output power. Therefore, following this way, a tricky compromise between RIA reduction and background losses has to be reached in order to build high performance optical amplifiers that may fulfill space applications requirements. A last well-known possible hardening possibility relies on the inclusion of Cerium in the silica matrix[8], as Cerium acts as a hole trap. However, whereas strong RIA reduction can be attained at signal wavelength[9], the insufficient RIA lowering at pump wavelength leads to complex Er-Yb double cladding optical fiber design, resulting in huge transparency power, thus to poor optical efficiency. Whereas such a fiber is suitable for specific high optical power applications, it cannot meet most satellite application requirements, in which power consumption is a key parameter. In this paper, we explore another EDF-hardening concept that, contrary to the aforementioned approaches, is based on the accurate physical origin of standard EDFs excessive degradation; indeed, like it has been done in the past with passive optical fibers, we look into the possibility to reduce the codoping atoms concentration. In the frame of this work, we thus explore the opportunity to reduce Aluminum concentration in the EDFs, while increasing the Erbium quantity in order to design shorter amplifiers. Unfortunately, following this way by means of classical fabrication techniques inherently leads to massive quenching effects that dramatically reduce the EDF efficiency[10]. For this reason, the fabrication of such an EDF relies on disruptive technologies concerning the inclusion of the Erbium in the silica glass, allowing to reduce or eliminate the Aluminum proportion while controlling the Erbium ions close neighborhood in order to minimize quenching effects[11]. In this paper, we take advantage of the glass nanostructuration to fabricate such optical fibers by means of silica or alumina Erbium-doped nanoparticles (NP)which are inserted in the glass matrix. We then compare their resistance to radiations with various EDFs fabricated by classical process, thanks to EDFA configurations and irradiation conditions chosen to approach space requirements. III.NANOPARTICLES-DOPED RADIATION-RESISTANT EDFS DESIGN AND FABRICATIONA.In this work, we take advantage of NP doping process [12], [13], [14] to manufacture rare earth doped fibers, allowing an accurate control of the rare earth doping characteristics (incorporation, dispersion, chemical environment)within the fiber core matrix. Rare earth doped NPs synthesized by soft chemical way are put in the frame of stable aqueous suspension and incorporated within optical preform through a classical liquid doping technique, whatever the chosen main core glass matrix composition. In the context of radiation insensitive fibers, manufacturing Er-doped fibers without Al-doping (SiO2/Er NPs)or with the minimal Al quantity (Al2o3/Er NPs)is now possible by involving NP doping technology. The Al2O3/Er NPs exhibit a determined atomic ratio Al/Er= 200, ensuring the WDM gain shape. In this case, a high Er content in the fiber can be reached thanks to a further optimization of doping porous layer capacity. Moreover, the NP process is interesting in an industrial context because it allows to perform a nanostructuration of the glass while being compatible with traditional MCVD fabrication process (fig. 1). B.In order to check the degradation of the EDFs, we built for each fiber a co-propagative EDFA configuration with 21 to 23 dBm pump power at 980 nm and 0 dBm 1550-nm signal power at the input. Each amplifier is simply designed by choosing the so-called ”optimal EDF length”, that allows to reach before irradiation the highest output power at signal wavelength for fixed pump and signal input powers. These EDFA configurations are sufficiently similar to compare the post-irradiation results in terms of gain reduction. The Erbium-doped fibers explored in this work are designed and chosen to demonstrate many points, such as the influence of Aluminum concentration and amplifier length, but also the benefits of the Erbium neighborhood control permitted by NP-CVD. The main parameters and properties of both EDF and EDFAs before irradiation are summed-up in Table I. TABLE IEDFS AND ASSOCIATED EDFA PARAMETERS, AND RIA VALUES. FIBERS ”NP-AL” AND ”NP-SI+” EXHIBIT LOWER OUTPUT POWER BECAUSE OF LOWER PUMP POWER. FOR 23 dBm PUMP POWER, ”NP-AL” WOULD EXHIBIT OUTPUT POWER CLOSE TO ”AL-LB”, WHILE ”NP-SI+” WOULD EXHIBIT OUTPUT POWER SIMILAR TO ”AL-NB” OR ”NP-SI”.
IV.IRRADIATION EXPERIMENTS, RESULTS AND DISCUSSIONSA.As displayed in fig. 2, the experimental set-up is made of two distinct parts:
All the EDFA measurements were performed ”in-line”. The coils of Er-doped fibers are linked to the instruments thanks to a set of 30 m-long HI1060 Flexcore optical fibers. The degradation of these passive optical fiber extensions can be ignored, as the RIA of passive fibers never exceeds some tens of dB/km[16] in the near to mid infrared range. This point was confirmed by post-irradiation transmittance measurements of the HI1060 Flexcore extensions. We have also to notice that the results exhibited here are pessimistic, compared to real-space mission conditions, because each fiber was illuminated only during each data acquisition and not continuously during the whole irradiation experiments. The impact of the photobleaching is thus not taken into account in this work, and the only possible recovery may come from the room-temperature. B.The gain decrease monitored inline for each EDFA is displayed in figure 3 as a function of the dose. These results clearly demonstrate the benefits obtained thanks to the NPCVD process. Our discussion describes two opposite ways, concerning the balance between low RIA and short amplifier length:
We also notice that comparing fibers ”NP-Si+” and ”NP-Si” corroborates the design rule from A. Gusarov et al. [4], bringing to the fore that fabricating shorter-length optical-amplifiers leads to radiation-resistant EDFA. However, this rule is to be weighted with the value of the RIA. Indeed, the ”short amplifier” design rule fits well with both ”NP-Si+” and ”NP-Si”, whereas it cannot work between ”NP-Si”, ”NP-Al” and ”Al-NB”, because of very different RIA values. Actually, whereas ”NP-Al” allows to reach very short optimal-length amplifier (down to 2.5 m), both ”Al-NB” and ”NP-Si” based EDFA exhibit similar or better resistance to radiations, while being more than 10 times longer. C.For these measurements, we take advantage of a low ASE ECDL (External Cavity Diode Laser). The Noise Factor was measured for both ”NP-Si+” and ”NP-Al” EDFA by using the ASE interpolation technique[19] and then calculated following the IEC (International Electrotechnical Commission)definition [20], considering the signal-ASE beat as the main noise contribution in the EDFA: ρASE is the amplified spontaneous emission spectral density (in W/Hz), and G the amplifier optical gain. We have to notice that the shot-noise contribution (+1/G)can be neglected in the NF calculation because the optical gain is still strong enough for each optical fiber after the 400 Gy irradiation. The results are summed-up in fig. 4. Due to the lack of Aluminum, the ASE spectrum of the NP-Si+ fiber does not take advantage of the Aluminum-induced inhomogeneous broadening of the emission cross sections (fig. 4-a and -b). For this pure-silica fiber, the ASE power is thus concentrated over a narrower spectral range than the one of an Aluminum codoped fiber. For that reason, the pure silica ASE optical power spectral density (PSD)is stronger, and this impacts the noise factor value. That’s what is observed in fig. 4-c. Nevertheless, we have to notice that, at this time, the NP-Si+ fiber design has not still been optimized to reduce the Noise Factor. We also bring to the fore that the noise factor degradation itself is lower than 1 dB after a 400 Gy deposit dose for the two kinds of NPs. Moreover, this degradation is, once more, a pessimistic result because the fibers did not experience any optical recovery. D.It is clear that the degradation of the EDFA is due to the increase of the RIA. However, measuring simply the degradation at the output of an EDFA which optimal length is determined before irradiation is pessimistic, because the RIA acts like a strong increase of the background losses of the amplifier, which also induces a change in the EDFA optimal length once it is irradiated. In order to investigate this point, we performed cut-back operations on non-irradiated and 1300 Gy irradiated amplifiers in order to follow the evolution of the optimal length. The results of this work are displayed in fig. 5 for a highly degraded (NP-Al)and slightly degraded (NP-Si+)optical fibers. This figure shows that the optimal length reduction is quite small (< 20%) for the slightly degraded fiber, whereas it reaches nearly 80 % for the Aluminum codoped fiber, leading to huge absorption at the fiber end. Moreover, we see in fig. 5-a that the maximal power postirradiation at signal wavelength is obtained for ≈ 0.5 m fiber length and is ≈ 18 dB stronger than the power reached at the end of the fiber, i.e. at the pre-irradiation optimal length. For that reason, the optimal length of a radiation-resistant optical amplifier may be choosen considering the post-irradiation optimal length instead of the pre-irradiation optimal length. V.CONCLUSIONIn this work, we compared the radiation-resistance performances of 5 EDFs having different chemical compositions and fabricated thanks to both classical and NPCVD fabrication processes. We measured on the one hand the optical gain and noise factor in a saturated amplifier configuration, and on the other hand the RIA for both pump and signal wavelengths, in a small-signal regime. These measurements were carried out in-line, under Co60 gamma radiation. We also performed cut-back measurements, before and after degradation. The strongest gain-degradation is observed for the amplifier using the ”standard” technology-based fiber with the highest Aluminum concentration, while the lowest gain-degradation, and also the lowest RIA levels, are noticed for the silica nanoparticles based fibers, with no trace of Aluminum. Therefore, this work demonstrates for the first time the feasibility of radiation-resistant single-channel EDFA designed for space applications. This work also allows to determine an order of magnitude of the fundamental limits of the degradation permitted with an erbium-doped pure-silica fiber. In order to target multiple-channel or low noise applications, these fibers must be enhanced concerning the inhomogeneous broadening. This can be performed by means of slight inclusion of Aluminum into the pure-silica Erbium-doped NPs, while using a minimal hydrogenation process in order to compensate the RIA. REFERENCESD. Caplan, M. Stevens, and B. Robinson,
“Free-space laser communications: global communications and beyond,”
ECOC,
(2009). Google Scholar
L. Troussellier, C. Chluda, M. Myara, J. Boch, L. Dusseau, P. Signoret, O. Gilard, M. Sotom, and J.-P. David,
“Dose rate effect on aluminium-codoped erbium fibers,”
Radiation Effects on Insulators,
(2007). Google Scholar
H. Henschel, O. Köhn, H. U. Schmidt, J. Krichhof, and S. Unger,
“Radiation-induced loss of rare earth doped silica fibres,”
IEEE Trans. on Nucl. Sci., 45
(3), 1552
–1557
(1998). Google Scholar
A. Gusarov, M. V. Uffelen, M. Hotoleanu, M. Thienpont, and F. Berghmans,
“Radiation Sensitivity of EDFAs Based on Highly Er-Doped Fibers,”
IEEE J. Lightw. Technol., 27
(11), 1540
–1545
(2009). Google Scholar
B. Brichard, A. L. Tomashuk, V. A. Bogatyrjov, A. F. Fernandez, S. N. Klyamkin, S. Girard, and F. Berghmans,
“Reduction of the radiation-induced absorption in hydrogenated pure silica core fibres irradiated in situ with gamma-rays,”
J. Non-Cryst. Solids, 353 466
–472
(2007). Google Scholar
O. Humbach, H. Fabian, U. Grzesik, U. Haken, and W. Heitmann,
“Analysis of OH absorption bands in synthetic silica,”
J. Non-Cryst. Solids, 203 19
–26
(1996). Google Scholar
E. Modone and G. Roba,
“OH reduction in preforms by isotope exchange,”
Electronics Letters, 17
(21), 815
–817
(1981). Google Scholar
B. D. Evans and G. H. Sigel,
“Radiation resistant fiber optic materials and waveguides,”
IEEE Trans. on Nucl. Sci., 22
(6), 2462
–2467
(1975). Google Scholar
M. Vivona, S. Girard, C. Marcandella, E. Pinsard, A. Laurent, T. Robin, B. Cadier, M. Cannas, A. Boukenter, and Y. Ouerdane,
“Durcissement aux radiations de fibres optiques dopées terres rares et d’amplificateurs à fibres optiques,”
JNOG,
(2010). Google Scholar
P. Myslinski,
“Effects of concentration on the performance of Erbium-Doped fiber amplifiers,”
J. Lightw. Technol., 15
(1), 112
–120
(1997). Google Scholar
D. Boivin, T. Fohn, E. Burov, A. Pastouret, C. Gonnet, O. Cavani, C. Collet, and S. Lempereur,
“Quenching investigation on new erbium doped fibers using MCVD nanoparticle doping process,”
in Proc. of SPIE,
75
(2010). Google Scholar
A. Pastouret, C. Gonnet, and E. Burov, “Amplifying optical fiber and production method,” (2010). Patent US 2010135627. A. Pastouret, E. Burov, D. Boivin, C. Collet, and O. Cavani, “Amplifying optical fiber and method of manufacturing,” (2010). Patent US 2010118388. E. Régnier, A. Pastouret, and E. Burov, “Ionizing radiation-resistant optical fiber amplifier,” (2010). Patent US2010142033. S. Girard, B. Tortech, E. Régnier, M. V. Uffelen, A. Gusarov, Y. Ouerdane, J. Baggio, P. Paillet, V. Ferlet-Cavrois, A. Boukenter, J.-P. Meunier, F. Berghmans, J. R. Schwank, M. R. Shaneyflet, J. A. Felix, E. Blackmore, and H. Thienpont,
“Proton and gamma-induced effects on erbium-doped optical Fibers,”
IEEE Trans. on Nucl. Sci., 54
(6), 2426
–2434
(2007). Google Scholar
E. Régnier, I. Flammer, S. Girard, F. Gooijer, F. Achten, and G. Kuyt,
“Radiation-induced attenuation at IR wavelength in silica based optical fibers,”
RADECS 2006,
(2006). Google Scholar
J. Thomas, M. Myara, L. Troussellier, E. Régnier, E. Burov, O. Gilard, M. Sotom, and P. Signoret,
“Experimental demonstration of the switching dose-rate method on doped optical fbers,”
in International Conference on Space Optics (ICSO),
(2010). Google Scholar
B. Brichard, A. F. Fernandez, H. Ooms, and F. Berghmans,
“Gamma dose rate effet in erbium-doped fibers for space gyroscopes,”
in Proc. of the 16th International Conference on Optical Fiber Sensors,
(2003). Google Scholar
D. Derickson, Fiber optic test and measurements, Prentice-Hall,1998). Google Scholar
D. M. Baney, P. Gallion, and R. S. Tucker,
“Theory and measurement techniques for the noise figure of optical amplifiers,”
Optical Fiber Technology, 6 122
–154
(2000). Google Scholar
|